Model 76 Classic 25th Anniversary #2 of 25
.30/06
Celebrating 25 years at the pinnacle of bolt-action
form and function, the Dakota® Model 76™ was developed by Don Allen and
Pete Grisel in 1986. It exemplifies the very best of bolt-action
innovation with the exquisite lines and impeccable shot-to-shot
precision created only through the individual attention of Dakota
craftsmen. The action combines the best features of the pre-64 Model 70,
with a Mauser-type extractor for controlled round feed and
ultra-positive extraction.
Today, the Dakota 76 is one of the most desirable hunting rifles in the
world, proven on every continent, in every climate, and on every type of
game. It has deservedly taken its place among the legendary rifles of
the 20th--and 21st centuries.
The Dakota 76 Classic features controlled round feeding and positive
extraction; the extractor, underneath the locking lug and positioned at
the end of the bolt, opens fully to insure that the next round feeds
smoothly. The three-position safety allows the bolt to be operated with
the safety on. The one-piece trigger guard and hinged floor plate are
machined from solid bar stock.
This is a very special rifle, only 25 of these will be made and this is
the very first. Serial number is 76 2 of 25. It has 25th anniversary
engraved on the floor plate and DA 2 on the grip cap. The receiver is
case colored and engraved. It has a hooded front and engraved bolt knob.
Also comes with a SKB hard case.
|
|
Model 10
.257ROBERTS
Machined from pre-hardened billet stock, the rear of the breech block and
receiver are solid walls of steel. There are no cuts or holes that could allow
escaping gases to reach a shooter's face. A crisp trigger pull and short hammer
fall provide fast lock times. The tang safety is smooth and quiet, equally
convenient for right or left-handed shooters. A strong positive extractor firmly
grips both rimmed and rimless cases. Straight tangs allow a stock design with a
high comb and good facial support, while minimizing the effects of recoil.
Model 10
-
Case Colored receiver
-
Case Colored Skeleton butt
-
Inlayed swivels
-
XXX English upgrade
|
|
Model 76 Safari
.375H&H
In 1986, Don Allen and Pete Grisel created the Dakota 76. It combines the best
features of the pre-64 Model 70 action with a Mauser-type extractor...along with
a number of innovations that are strictly Dakota.
Today, the Dakota 76 is one of the most desirable hunting rifles in the world,
proven on every continent, in every climate, and on every type of game. It has
deservedly taken its place among the legendary rifles of the 20th--and 21st
centuries.
The Dakota 76 is offered in Classic, Safari and African grades. They all feature
controlled round feeding and positive extraction; the extractor, underneath the
locking lug and positioned at the end of the bolt, opens fully to insure that
the next round feeds smoothly. The three-position safety allows the bolt to be
operated with the safety on. The one-piece trigger guard and hinged floor plate
are machined from solid bar stock.
Every Dakota 76 can be custom-tailored to your size and tastes, with a wide
range of optional features available
Standard Features -
Safari
- XXX fancy walnut, cheek piece with shadow line,
point wrap checkering on forend, ebony forend tip, barrel band and
inletted Ken Howell swivel studs, 13 5/8" length of pull, 1" black
recoil pad
- Front island sight with flip-up night sight,
rear island with blade
- Standard, long, short magnum, long magnum and
Rigby length actions, 23" barrel
- Right- or left-hand configurations Approximate
weight 8,5 lbs
- Straddle floorplate with inside release, drop
belly magazine with four-round capacity
|
 |
Model 76 Safari
In 1986, Don Allen and Pete Grisel created the Dakota 76. It combines the best
features of the pre-64 Model 70 action with a Mauser-type extractor...along with
a number of innovations that are strictly Dakota.
Today, the Dakota 76 is one of the most desirable hunting rifles in the world,
proven on every continent, in every climate, and on every type of game. It has
deservedly taken its place among the legendary rifles of the 20th--and 21st
centuries.
The Dakota 76 is offered in Classic, Safari and African grades. They all feature
controlled round feeding and positive extraction; the extractor, underneath the
locking lug and positioned at the end of the bolt, opens fully to insure that
the next round feeds smoothly. The three-position safety allows the bolt to be
operated with the safety on. The one-piece trigger guard and hinged floor plate
are machined from solid bar stock.
Every Dakota 76 can be custom-tailored to your size and tastes, with a wide
range of optional features available
Standard Features -
Safari
- XXX Bastogne Walnut, cheek piece with
shadow line,
point wrap checkering on forend, ebony forend tip, barrel band and
inletted Ken Howell swivel studs, 13 5/8" length of pull, 1" black
recoil pad
- Scope base & rings
- Front island sight with flip-up night sight,
rear island with blade
- Standard, long, short magnum, long magnum and
Rigby length actions, 23" barrel
- Right- or left-hand configurations Approximate
weight 8,5 lbs
- Straddle floorplate with inside release, drop
belly magazine with four-round capacity
|
|
Model 76 Classic
6.5x284
.30/06
.270
In 1986, Don Allen and Pete Grisel created the Dakota 76. It combines the best
features of the pre-64 Model 70 action with a Mauser-type extractor...along with
a number of innovations that are strictly Dakota.
Today, the Dakota 76 is one of the most desirable hunting rifles in the world,
proven on every continent, in every climate, and on every type of game. It has
deservedly taken its place among the legendary rifles of the 20th--and 21st
centuries.
The Dakota 76 is offered in Classic, Safari and African grades. They all feature
controlled round feeding and positive extraction; the extractor, underneath the
locking lug and positioned at the end of the bolt, opens fully to insure that
the next round feeds smoothly. The three-position safety allows the bolt to be
operated with the safety on. The one-piece trigger guard and hinged floor plate
are machined from solid bar stock.
Every Dakota 76 can be custom-tailored to your size and tastes, with a wide
range of optional features available
Standard Features - Classic
- XX fancy walnut, hand-rubbed oil finish, point
panel checkering, Dakota swivel studs, 13 5/8" length of pull, 1"
black recoil pad
- Short, standard and long actions, 23" barrel
- Right-hand configurations
- Approximate weight 6.5 to 7.5 lbs
- with out sights
|
 |
Predator Prairie
.20TAC
***JEWEL TRIGGER***
.20TAC
.204RUGER
***JEWEL TRIGGER***
.22PPC
***JEWEL TRIGGER***
.223
***JEWEL TRIGGER***
.223
6.5GRENDAL
***JEWEL TRIGGER***
6.8SPC
***JEWEL TRIGGER***
|
 |
Predator Mountain
.223
6.5GRENDAL
.222REMINGTON
.17REMINGTON FIREBALL
.204RUGER ***JEWEL TRIGGER***
.204RUGER |
|
Longbow ***IN STOCK***
.338LAPUA
The Longbow was developed from the ground up at the request of one of
the world's more sophisticated governments, seeking a tactical military
rifle of unprecedented accuracy, power and flexibility. Based on Dakota
Arms' renowned Model 76 hunting action, the Longbow offers range and
power vastly superior to .30 tactical rifles, without the weight and
bulk of .50 weapons.
The Longbow guarantees 1/2 MOA performance with an effective range of
1500 meters in its .338 configuration. It generates up to 5250 ft. lbs.
of muzzle energy from a 300 grain bullet traveling at 2850 fps. The
rifle is available in .338Lapua magnum, .330 Dakota magnum, and .300
Dakota magnum. It utilizes commercially available match grade ammunition
and components.
| Specifications |
| Size/Weight
|
Length: 50" to 51 1/2"
Weight: 13.7 Pounds without scope |
| Action |
· Machined high strength steel alloy
square bottom action
· Blind magazine
· Dakota Arms 76-style 3-position firing pin block safety
· Controlled round feeding
· Single round feeding
· Dakota Arms 76-style bolt release
· Matte Finish
· Claw extraction system
· Positive Mechanical Ejector
· Model 70 style trigger (will not seize from dirt or freeze in
rain)
· 2.5 lb. trigger pull
· Picatinny one-piece optical rail, secured with 8-40 screws |
| Stock |
· Ergonomic, ambidextrous A-2
McMillan Fiberglass stock, black or olive drab green
· Full length action bedding
· 1 1/2" adjustable length of pull, from 12 7/8" to 14 3/8"
· Adjustable cheek piece
· 3 sling swivel studs
· Bipod spike in forend |
| Barrel |
· High integrity LW-50 stainless
steel (proprietary to Lothar Walthar)
· 28" .950 at muzzle
· High efficiency tuned muzzle brake |
| Deployment Kit |
· One Case: double wall, lockable,
airline approved, 53 1/2" x 14 1/4" x 4 5/8"
· One front bipod spike
· OPERATORS TOOL KIT:
1 torque wrench 65 in-lbs.
1 3/16 Allen head socket (for installing action screws)
1 1/2" hex socket (for installing scope rings)
1 1/2" combination wrench (for removing scope)
1 3/32" Allen wrench for scope rings
1 5/32" Allen wrench for front guard screws
1 3/16" Allen wrench for action screws
1 tool kit box |
|
 |
Traveler Take Down
7mmSTW
.375H&H
Created for the traveling hunter, the
Traveler is a Model 76 that takes down into two sections: the
receiver/stock and barrel/forend. It packs in a small case, and you can
easily add a second barrel. For example, combine a .300 H&H with a .375
H&H, or a 7mm Dakota with a .404 Dakota, and you have the ultimate
African plains and big game combination in a compact, easy-to-transport
package. Individual Traveler rifles can be built in virtually any
caliber; however, multiple barrel/caliber combinations must be chosen
from within the same family of calibers.
Standard Features - Safari
- XXX fancy walnut, cheek piece with shadow line, point wrap
checkering on forend, ebony forend tip, barrel band and inletted Ken
Howell swivel studs, 13 5/8" length of pull, 1" black recoil pad
- Front island sight with flip-up night sight, rear island with
blade
- Standard, long, short magnum, long magnum and Rigby length
actions, .23" barrel
- Right- or left-hand configurations
- Approximate weight 8.5 lbs
- Straddle floor plate with inside release, drop belly magazine
with four-round capacity (most calibers)
- Talley base with 1in & 30mm rings
|
 |
